Black + Decker Drill Problems: 7 Common Issues (with simple fixes)

Like all Black + Decker appliances, Black + Decker tools are well-made and long-lasting.

However, drills, like all machines, are prone to malfunction, causing you to become frustrated if you are unable to complete your DIY project.

Before you give up and borrow your neighbor’s drill, read this article first.

Black + Decker Drill Not Working

The drill will not spin or make any noise when the trigger is pulled.

The most common reasons why a Black + Decker drill not working include a faulty battery, one that hasn’t been charged, a problem with the motor, or a damaged trigger switch. 

Solution/s

  • If you have a spare battery, connect it to the drill to see if it works. If the drill does not work, try charging a battery. Turn on the battery to see if it charges. If the battery charges and the drill still does not work, but the trigger works, the problem is most likely with the motor. If the battery did not charge, proceed to the next step.
  • Try the charger on another outlet to see whether the outlet is functional. Replace the charger with a new one if the outlet is functional because the problem may be with the charger itself.
  • Push the battery into the drill until it is firmly attached to ensure that it is connected. Verify that the battery is completely charged. Try a fresh battery if everything else fails.
  • If it still doesn’t work, make sure the battery is in good contact with the power terminals in the handle. The signal wires at the soldered connector inside the hand may have been broken due to vibration.
  • Finally, inspect the trigger switch, ensuring it still works as normal.

If your Black + Decker Drill still does not work, the problem is most likely with the motor. It is best to have it replaced if it is still under warranty or to buy a new one.

Black + Decker Drill Not Charging

The most common reason for a Black + Decker drill not charging is that the battery was not properly inserted into the charger, the charger has been damaged, the charger was not plugged in, or the charger or battery is faulty.

Solution/s

  • Firstly, ensure the battery is correctly placed in the charger, and that the charger is clean from any grease, dirt, or dust.
  • To test whether the outlet is working, try the charger on a different outlet. If the outlet is working, replace the charger with a new one because the issue can be with the charger itself.
  • Push the battery into the drill until it is firmly attached to ensure that it is connected. Verify that the battery is completely charged. Try a fresh battery if everything else fails.

If you still can’t get the battery to charge, Black + Decker has a service that allows batteries to be checked at one of their Service Centers. More information is available at the link provided below.

How do I test the battery to determine if there is a bad cell? – BLACK+DECKER (blackanddecker.com)

Black + Decker Drill Not Holding Charge

You’re halfway through your job and your drill is starting to slow down.

Do you notice that your Black + Decker drill isn’t lasting as long as it used to?

The most common reason why the Black + Decker drill not holding charge is

Solution/s

  • If the drill is still working intermittently or not at all, make sure the battery is correctly inserted into the charger and that the charger is free of grease, dirt, and dust.
  • If the problem persists, check the outlet and try the charger on a different outlet. If the outlet is operational, replace the charger because the problem could be with the charger itself.

Black + Decker Drill Not Spinning

Your Black + Decker drill bit might stop spinning if it is inserted incorrectly or is under excessive pressure. Mechanical problems with the drill may also affect the bit’s capacity to spin.

It’s possible that problems with the chuck, gears or gear cases are to blame for a drill that won’t spin.

Solution/s

Excessive Pressure

When the drill isn’t spinning quickly enough, the bit can stop spinning due to excessive pressure after it makes contact with the surface.

As you attempt to use the drill, ease off on the pressure. If the problem is with your handling, the bit should start spinning; however, if the drill isn’t spinning quickly enough, make sure to check the battery capacity if you’re using a cordless drill.

Faulty Trigger Switch

To rotate in either the forward or reverse direction, make sure the actuator (forward/reverse button) is fully depressed. If the trigger still won’t pull, there may have been a mechanical issue with the trigger, in which case a new switch is needed.

The switch might be broken if the trigger pulls but the motor does not turn on. You must take apart the drill casing to check to see if the switch is broken.

Check out this step-by-step guide on how to replace the switch

Faulty Transmission

A transmission issue is present if the motor is running but the chuck is not turning. An indication that the gears inside the gearbox might not have been properly seated is slow spinning or no spinning at all.

Verify that the gearbox has fully transitioned to the desired gear and is not in-between gears.

If it still won’t spin, the transmission might be broken and needs to be replaced.

This guide will take you through steps to replace faulty transmission

Faulty Motor

A faulty motor can cause the chuck to spin slowly or not at all. Overloading the motor or wearing out the brushes within the motor can cause the motor to fail. In either case, the motor will need to be replaced.

Use this guide to learn how to remove and replace a drill motor.

If you are still experiencing problems, contact Black + Decker or the place of purchase. 

Black + Decker Drill Stopped Working

Black + Decker drills rarely stop working, but when they do, it’s usually because the battery has started to fail or is running low on power.

Solution/s

  • Make sure the battery is firmly inserted into the drill to make sure it is connected. Make sure the battery is fully charged.
  •  If still not working, try a new battery.
  • If the problem persists, check the outlet and try the charger on a different outlet. If the outlet is operational, replace the charger because the problem could be with the charger itself.

Black + Decker Drill Not Tightening

If your Black + Decker drill bit keeps coming loose, it’s because your drill’s chuck is worn out, dirty, and grimy, or it’s not locking properly. To fix the problem, clean your drill, replace the chuck, or, if less expensive, buy a new drill.

Black + Decker Drill Not Releasing

The chuck on your drill is worn out, dirty, and grimy, or it is not locking properly, which is why your Black + Decker drill bit keeps coming loose. To resolve the issue, clean your drill, replace the chuck, or, if more cost-effective, purchase a new drill.

Black + Decker Drills Any Good?

Yes, Black + Decker drills are good. Suitable for those on a limited budget. Black + Decker drills handle light-duty tasks with ease. It’s not necessarily a good choice for the enthusiastic DIYer, and it’s certainly not a good choice for a pro, but if you only need a drill for hanging picture frames or assisting with furniture assembly, Black+Decker is a great choice.

How Long Do Black + Decker Drills Last?

The lifespan of a drill is determined by how frequently it is used, and the type of drilling performed.

When used infrequently and with less difficult drilling, it will last for years, as opposed to constant use and hard drilling.

A fully charged battery on a cordless drill lasts eight hours and has a lifecycle of two to five years. Manufacturers claim that these batteries should last at least 1,000 charging cycles.

Pros and Cons of Black + Decker Drills

Here are some of the pros and cons of Black + Decker drills 

Pros

  • Inexpensive
  • Lightweight
  • Well built

Cons

  • Not rugged enough for a construction site

Conclusion

If you need a low-cost drill for DIY projects around the house, go with the Black + Decker brand.

However, you may encounter some difficulties, hopefully later rather than sooner.

In that case, the solutions listed above will come in handy.

So keep them in mind at all times and your Black + Decker drill in good working order.

Related Articles

References