Sunbeam Stand Mixer Problems: 7 Common Issues (Simple Fixes)

Stand mixers are one of the most useful tools you can get for your kitchen.

Whether you need to mix cookie dough or bake something, a stand mixer comes in handy for every recipe that requires stirring.

What’s best is that having a Sunbeam stand mixer can further ease your cooking.

However, at times, your Sunbeam stand mixer might run into issues.

So, keep reading to avoid common problems.

Sunbeam Stand Mixer Not Turning On

A working Sunbeam mixer should turn on in an instant after pressing the on/off switch.

If your Sunbeam stand mixer does not turn on, it is most likely because it is not plugged in, or there is a problem with the socket or cord.

Follow the solutions mentioned below to fix the mixer.

Possible Solution(s):

  • Start by checking the outlet by plugging in a different working device. If the device does not work, you will need to plug in your mixer in a different socket.
  • Alternatively, you can check the circuit breaker switch for that particular socket and make sure it isn’t turned off to allow power to the mixer.
  • If all solutions above fail to work, the power cord may be faulty.
  • You can test the power cord with a voltmeter and have it replaced if it’s defective.

Best to contact an appliance repair technician for help

Connect with an Appliance Repair Technician
Click here to use the chatbox to speak with one of our skilled technicians.
No in-home service calls. No appointments.

Sunbeam Stand Mixer Not Locking In

Sunbeam stand mixer not locking in is typically caused by the beater being too high on a tilt head mixer, thereby preventing the head from locking into place.

Before mixing, the mixer’s head must lock in facing downwards to avoid spilling its contents outside due to free movement.

If you notice your mixer’s head moving up and down while mixing, follow the solutions below.

Possible Solution(s):

  • Typically, this issue can easily be fixed by setting the mixer’s head height slightly higher than it was before.
  • However, if doing so does not solve the problem, you will need to call a professional to fix the issue, as it can get quite technical.

Best to contact an appliance repair technician for help

Connect with an Appliance Repair Technician
Click here to use the chatbox to speak with one of our skilled technicians.
No in-home service calls. No appointments.

Sunbeam Stand Mixer Stopped Working

If your Sunbeam stand mixer has suddenly stopped working or isn’t spinning after turning it on, there is an internal issue it’s facing.

Continue to read the solutions mentioned below to fix your mixer.

Possible Solution(s):

  • The most common reason behind this issue is a faulty motor that has overheated. To replace the motor, you will need to get help from an expert.
  • If the motor is working fine, disassemble the mixer and make sure wires are connected properly to the speed control plate and the phase control board.

Best to contact an appliance repair technician for help

Connect with an Appliance Repair Technician
Click here to use the chatbox to speak with one of our skilled technicians.
No in-home service calls. No appointments.

Sunbeam Stand Mixer Making Loud Noise

It’s normal for a Sunbeam mixer to make some noise while mixing.

However, if you discover that your Sunbeam mixer is making more noise than usual, it’s probably because some food debris or other foreign object got lodged inside of it.

You can disassemble the mixer, look inside, and get rid of the thing.

Check out the instructions below if you are unable to find the unwanted object.

Possible Solution(s):

  • One of the most common reasons behind this issue is a failed worm gear. Try replacing the worm gear to reduce the noise.
  • If the worm gear isn’t the cause of the issue, you will need to apply new grease to the gears of the mixer and remove the old grease.

Sunbeam Stand Mixer Not Spinning

If you’ve turned on your Sunbeam mixer, but it fails to function properly and do its job, it’s facing an internal issue that is preventing it from spinning.

Here are some solutions to fix the issue.

Possible Solution(s):

  • Usually, if your Sunbeam mixer stops working, it’s due to a worn-out worm gear that plays an important role in the spinning mechanism.
  • To fix the mixer, you will need to replace the worm gear with a new one by disassembling the mixer from the top.

Sunbeam Stand Mixer Only Working at Specific Speeds

If your mixer only spins at certain speeds and fails to function at other levels of speed, there’s something wrong with its internal parts.

Here are some solutions to help you solve the issue.

Possible Solution(s):

  • A common reason for this issue is a loosely connected hall sensor. The hall sensor is the grey wire connecting the speed lever and the control board. Connect it properly and check if the mixer works.
  • If the hall sensor is connected properly, you will need to replace the circuit board.

Best to contact an appliance repair technician for help

Connect with an Appliance Repair Technician
Click here to use the chatbox to speak with one of our skilled technicians.
No in-home service calls. No appointments.

Sunbeam Stand Mixer Leaking Oil

Sunbeam mixers are manufactured with grease packed inside them to lubricate gears and prevent machinery from being worn out.

But it can become a problem when the grease starts to leak as oil. Here are some solutions to help you solve the issue.

Possible Solution(s):

  • The only way to solve the issue is to remove the old grease and replace it with new grease. You will need to call a professional for this purpose.
  • Alternatively, you can turn on the mixer and remove the excess oil before adding food to it. Even if there is some oil seeping into the food, it won’t be harmful as it’s food grade.

Sunbeam Stand Mixer Still Not Working?

The solutions mentioned above can be used to solve a wide range of different issues with Sunbeam stand mixers.

However, sometimes, the problem can be of a more technical nature, requiring a different solution.

If that’s the case with you and your stand mixer fails to work even after trying out all the solutions mentioned above, you may need to contact a professional.

But you can also try taking a look at the user manual that came along with the stand mixer. Follow the steps for troubleshooting in the user manual and fix the problem accordingly.

Connect with an Appliance Repair Technician
Click here to use the chatbox to speak with one of our skilled technicians.
No in-home service calls. No appointments.

How Long Do Sunbeam Stand Mixers Last?

Sunbeam is a well-known brand in the kitchen appliance industry. Not only does Sunbeam produce some of the most innovative products with great features and looks, but it also has long-lasting and durable products.

The Sunbeam stand mixer is no different.

As a result, it’s safe to conclude that the Sunbeam mixer can last several years without facing any problems.

How To Maintain Sunbeam Mixer

Keeping your Sunbeam mixer in good condition through regular maintenance can help you increase its lifespan and avoid common problems like those mentioned above.

Cleaning your stand mixer every couple of days is a great way to maintain your Sunbeam stand mixer. This prevents dirt from getting inside the machinery of the mixer and causing issues.

Furthermore, you can also add grease to the gears of the mixer to reduce friction and allow it to function as well as new.

Sunbeam Mixers Any Good?

Yes, Sunbeam mixers are very good. Sunbeam is known to create long-lasting, well-designed durable mixers.

Sunbeam mixers are significantly less expensive than the majority of the best stand mixers (opens in new tab). Is effective at certain kitchen tasks, such as mixing cookie dough, and it carries the brand name and excellent reputation of a company that has been manufacturing appliances for over a century.

More importantly, Sunbeam mixers come with smart features that allow you to use and clean them with ease.

Therefore, Sunbeam manufactures some of the best stand mixers available in the market.

Pros and Cons of Sunbeam Mixers

Here are some pros and cons of Sunbeam mixers.

Pros

  • Easy to use.
  • Good quality
  • Great performance

Cons

  • Can be noisy.

Conclusion

Adding a Sunbeam mixer to your kitchen is one of the best things you can do to ease your cooking.

After all, it’s a great tool and can be quite useful in preparing several different dishes.

However, just like every other machine, it’s prone to failure at times.

So, keep in mind the solutions mentioned above and follow them if your Sunbeam mixer fails to function.

Related Articles

References